![Laughing :lol:](./images/smilies/icon_lol.gif)
General welding questions that dont fit in TIG, MIG, Stick, or Certification etc.
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Has anybody else had one of those days where you can't do a good bead to save your life or cut anything square or dip your tungsten all day and everything you touch falls apart in your hands? The universe was not my friend today ![Laughing :lol:](./images/smilies/icon_lol.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
- AKweldshop
-
Weldmonger
-
Posts:
-
Joined:Wed Oct 23, 2013 3:30 pm
-
Location:Palmer AK
Yes!! ![Laughing :lol:](./images/smilies/icon_lol.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
Just a couple welders and a couple of big hammers and torches.
Men in dirty jeans built this country, while men in clean suits have destroyed it.
Trump/Carson 2016-2024
Men in dirty jeans built this country, while men in clean suits have destroyed it.
Trump/Carson 2016-2024
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
For me it's more a matter of not knowing how to weld in the first place!
Also, yesterday I reckon I forgot about 10 times to re-attach my earth as I moved the workpiece about. Bzzt. Psshh. Sigh.
Kym
Also, yesterday I reckon I forgot about 10 times to re-attach my earth as I moved the workpiece about. Bzzt. Psshh. Sigh.
Kym
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
My hi-frequency always reminds me when I forget to ground. It's more startling than painful but it still pisses me off.MosquitoMoto wrote:For me it's more a matter of not knowing how to weld in the first place!
Also, yesterday I reckon I forgot about 10 times to re-attach my earth as I moved the workpiece about. Bzzt. Psshh. Sigh.
Kym
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
Jim FLinchbaugh
- Jim FLinchbaugh
-
Workhorse
-
Posts:
-
Joined:Thu Sep 01, 2016 11:56 pm
-
Location:Kalispell Montana
John Chamorro
- John Chamorro
-
Guide
-
Posts:
-
Joined:Thu Mar 19, 2015 9:44 am
-
Location:San Antonio Valley Peoples Republic of Californy
I quit counting the bad days and now count the good days. It's easier because there's less of them. I've always had a 3 mistake rule. 1 mistake was a whoops. 2 mistakes and something needs to change. 3rd mistake and I quit for the day. Now I quit at 2.
I don't know it all but I'm working on it.
ex framie
- ex framie
-
Ace
-
Posts:
-
Joined:Sun Aug 09, 2015 1:09 am
-
Location:Brisbane QLD Land of oz
I now know why my level of paranoid feelings have gone off the chart, you're all bloody well watching me stuff up.
You've mentioned it ALL.
Main issue is that my welding is marginal at best and then I may not need to weld anything for weeks or months.
Back to step one every time for the first couple of practice welds, then achieve mediocrity till next time.
I know more seat time, but this is a hobby, not a living, if it was a living, I'd be skinny......
You've mentioned it ALL.
Main issue is that my welding is marginal at best and then I may not need to weld anything for weeks or months.
Back to step one every time for the first couple of practice welds, then achieve mediocrity till next time.
I know more seat time, but this is a hobby, not a living, if it was a living, I'd be skinny......
Pete
God gave man 2 heads and only enough blood to run 1 at a time. Who said God didn't have a sense of humour.....
God gave man 2 heads and only enough blood to run 1 at a time. Who said God didn't have a sense of humour.....
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
Framie -ex framie wrote:I now know why my level of paranoid feelings have gone off the chart, you're all bloody well watching me stuff up.
You've mentioned it ALL.
Main issue is that my welding is marginal at best and then I may not need to weld anything for weeks or months.
Back to step one every time for the first couple of practice welds, then achieve mediocrity till next time.
I know more seat time, but this is a hobby, not a living, if it was a living, I'd be skinny......
Everyone's talking about your paranoia.
Kym
- weldin mike 27
-
Weldmonger
-
Posts:
-
Joined:Fri Apr 01, 2011 10:59 pm
-
Location:Australia; Victoria
Among other things, I sometimes forget that I'm stick welding and think I'm migging. Then wonder why my arc length gets super long as my hands are braced on the bench instead of traveling in with the rod.
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Or notMosquitoMoto wrote:Framie -ex framie wrote:I now know why my level of paranoid feelings have gone off the chart, you're all bloody well watching me stuff up.
You've mentioned it ALL.
Main issue is that my welding is marginal at best and then I may not need to weld anything for weeks or months.
Back to step one every time for the first couple of practice welds, then achieve mediocrity till next time.
I know more seat time, but this is a hobby, not a living, if it was a living, I'd be skinny......
Everyone's talking about your paranoia.
Kym
![Laughing :lol:](./images/smilies/icon_lol.gif)
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
I bought a piece of what I thought was stainless from my metal supplier. They sell metal drops for small projects and being that it was on the SS table, I just assumed it was SS. I cut it and formed it into a ring for a sleeve for a tube STILL not realizing it wasn't SS and even went as far as to weld it. It was 16ga. material so I set up the tig with a 1/16" gas lens and lit up on it and it would weld but the weld would snap as soon as it cooled. Turns out the piece was aluminum.
I am either getting old or drinking too much or a combination of the 2. True story...don't tell anyone ![Laughing :lol:](./images/smilies/icon_lol.gif)
![Embarrassed :oops:](./images/smilies/icon_redface.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
billdacat
- billdacat
-
New Member
-
Posts:
-
Joined:Tue Sep 20, 2016 1:22 pm
-
Location:New Jersey (Yeah it sucks)
I bought a bunch of 2.5" flat cold rolled steel of various thickness. Cut it up into 4.5" length's. Anytime I forget to weld or need to try something out, I can grab a couple of pieces and get a little practice before I commit to burning holes in something.
Great for dialing in vertical and overhead, especially different thickness.
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
Great for dialing in vertical and overhead, especially different thickness.
I once plugged my leads into the high and low instead of one of low and ground....rod would immediately stick and catch fire
just before i threw the welder across the garage, i managed to stop and walk around. felt pretty stupid when i walked back and saw what i had done ![Shocked :shock:](./images/smilies/icon_eek.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
![Shocked :shock:](./images/smilies/icon_eek.gif)
- ldbtx
-
Heavy Hitter
-
Posts:
-
Joined:Thu Jun 13, 2013 12:54 am
-
Location:North Central Texas
-
Contact:
Yeah, that's one of my usual screw-ups too. I MIG so much more than I use stick, that when I see an arc, I expect to have wire feeding into it.weldin mike 27 wrote:Among other things, I sometimes forget that I'm stick welding and think I'm migging. Then wonder why my arc length gets super long as my hands are braced on the bench instead of traveling in with the rod.
Miller Bobcat 225
Tweco Fabricator 211i
AHP AlphaTIG 200x
Lincoln SP-135+
Hypertherm Powermax 30 Air
ProStar O/A torch
Tweco Fabricator 211i
AHP AlphaTIG 200x
Lincoln SP-135+
Hypertherm Powermax 30 Air
ProStar O/A torch
- LtBadd
-
Weldmonger
-
Posts:
-
Joined:Sun Apr 12, 2015 4:00 pm
-
Location:Clearwater FL
-
Contact:
I guess as you were rolling it you must have thought what a good fabricator you were as that sst rolled so easyexnailpounder wrote:I bought a piece of what I thought was stainless from my metal supplier. They sell metal drops for small projects and being that it was on the SS table, I just assumed it was SS. I cut it and formed it into a ring for a sleeve for a tube STILL not realizing it wasn't SS and even went as far as to weld it. It was 16ga. material so I set up the tig with a 1/16" gas lens and lit up on it and it would weld but the weld would snap as soon as it cooled. Turns out the piece was aluminum.I am either getting old or drinking too much or a combination of the 2. True story...don't tell anyone
![Laughing :lol:](./images/smilies/icon_lol.gif)
Don't worry, no one knows...
Richard
Website
Website
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
LOL...thanks for keeping it a secret..that would be very embarrassing if it ever got out.LtBadd wrote:I guess as you were rolling it you must have thought what a good fabricator you were as that sst rolled so easyexnailpounder wrote:I bought a piece of what I thought was stainless from my metal supplier. They sell metal drops for small projects and being that it was on the SS table, I just assumed it was SS. I cut it and formed it into a ring for a sleeve for a tube STILL not realizing it wasn't SS and even went as far as to weld it. It was 16ga. material so I set up the tig with a 1/16" gas lens and lit up on it and it would weld but the weld would snap as soon as it cooled. Turns out the piece was aluminum.I am either getting old or drinking too much or a combination of the 2. True story...don't tell anyone
![]()
Don't worry, no one knows...
![Laughing :lol:](./images/smilies/icon_lol.gif)
![Confused :?](./images/smilies/icon_e_confused.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Bingo! But I drink twist off cheap beer...now whatPoland308 wrote:Super Glue a magnet to your bottle opener. Mystery metal problem solved!
![Laughing :lol:](./images/smilies/icon_lol.gif)
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
Return to “Welding Forum General Shop Talk”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities