the long and winding cart build
Posted: Tue Feb 17, 2015 5:24 pm
took forever but its finished..(i think)
Welding Tips and Tricks
The Forum
https://forum.weldingtipsandtricks.com/
the long and winding cart build
https://forum.weldingtipsandtricks.com/viewtopic.php?f=9&t=7009
Page 1 of 1
Re: the long and winding cart build
Posted: Tue Feb 17, 2015 5:31 pm
Nice cart, like the sliding plate for the cooler
Re: the long and winding cart build
Posted: Tue Feb 17, 2015 6:25 pm
I saw the first pic and was like hmm where's the tig lol. That a nice looking cart. Might have to steal that slide for the water cooler for mine. Nice work!
Re: the long and winding cart build
Posted: Tue Feb 17, 2015 10:12 pm
That's a nice looking set up. Well done.
Cheers.
-Eldon
Cheers.
-Eldon
Re: the long and winding cart build
Posted: Wed Feb 18, 2015 6:59 am
wes
figured i would show that photo before
someone asked how do i get the side door
on the mig to open with the welding rods
in the way.
the mig was an after thought on the cart.
craig
figured i would show that photo before
someone asked how do i get the side door
on the mig to open with the welding rods
in the way.
the mig was an after thought on the cart.
craig
Re: the long and winding cart build
Posted: Wed Feb 18, 2015 3:23 pm
Nice! What are your shelf tops and slide top made from? Lots of thought went into that cart 
Re: the long and winding cart build
Posted: Wed Feb 18, 2015 6:55 pm
ex
had a sheet of 1/8" 6063 alum i cut up
for shovels.
draw was from old desk in my work office
that i cut down.
connections from alum to steel are with riv-nuts.
craig
had a sheet of 1/8" 6063 alum i cut up
for shovels.
draw was from old desk in my work office
that i cut down.
connections from alum to steel are with riv-nuts.
craig
Re: the long and winding cart build
Posted: Wed Feb 18, 2015 7:06 pm
ex
truth being cart was designed for tig only but
half way through i realized i had enough room
to fit mig.. at that point plan A went to s##t and
the wing it factor came to play. lucky everything
fits. lol
craig
truth being cart was designed for tig only but
half way through i realized i had enough room
to fit mig.. at that point plan A went to s##t and
the wing it factor came to play. lucky everything
fits. lol
craig
Re: the long and winding cart build
Posted: Wed Feb 18, 2015 9:15 pm
Nice work. Its nice to do something for yourself once in awhile. I am trying to finish my new welding table but I am so busy welding I am using it unfinished. I am dying to try out my new Syncrowave 210 but can't find time. Friday it will happen! Keep them pics coming...this thread has gone cold 
Re: the long and winding cart build
Posted: Wed Feb 18, 2015 9:19 pm
Hey Craig...I see the Syncro 250...just wondering about the invertig...did you just want an inverter or does the 250 spin the electric meter to hard?
Re: the long and winding cart build
Posted: Thu Feb 19, 2015 7:09 am
ex
wanted an inverter for the size and yes too
keep the meter from spinning so much
plus smaller foot print. i will be retiring
and moving my stuff to my other house
so if the inverter works out ill sell the
250. one less machine to move.
i have a garage full of stuff......
craig
wanted an inverter for the size and yes too
keep the meter from spinning so much
plus smaller foot print. i will be retiring
and moving my stuff to my other house
so if the inverter works out ill sell the
250. one less machine to move.
i have a garage full of stuff......
craig