Page 1 of 1
Custom barrel stand.
Posted: Wed Feb 11, 2015 4:21 pm
by AKweldshop
1 1/2" angle iron. 1/8" thick.
Angles cut on the corners.
Fitting up into a square frame.
- IMG_1771.JPG (101.99 KiB) Viewed 1489 times
- IMG_1774.JPG (47.57 KiB) Viewed 1489 times
- IMG_1777.JPG (93.24 KiB) Viewed 1489 times
Re: Custom barrel stand.
Posted: Wed Feb 11, 2015 4:24 pm
by AKweldshop
- IMG_1778.JPG (54.04 KiB) Viewed 1488 times
- IMG_1784.JPG (85.47 KiB) Viewed 1488 times
- IMG_1785.JPG (43.59 KiB) Viewed 1488 times
Re: Custom barrel stand.
Posted: Wed Feb 11, 2015 4:27 pm
by AKweldshop
- IMG_1786.JPG (106.66 KiB) Viewed 1488 times
- IMG_1788.JPG (57.3 KiB) Viewed 1488 times
- IMG_1793.JPG (81.98 KiB) Viewed 1488 times
Re: Custom barrel stand.
Posted: Wed Feb 11, 2015 4:30 pm
by AKweldshop
- IMG_1798.JPG (79.46 KiB) Viewed 1488 times
- IMG_1797.JPG (81.35 KiB) Viewed 1488 times
- IMG_1799.JPG (81.51 KiB) Viewed 1488 times
Re: Custom barrel stand.
Posted: Thu Feb 12, 2015 6:28 pm
by RookieWelder
Nicely done! Nothing wrong with that project that I can see.
Dwight
Re: Custom barrel stand.
Posted: Thu Feb 12, 2015 8:06 pm
by Bill Beauregard
Have you considered adding four more pieces of angle to make it an octagon it sits on instead of a square, It would add strength.
Re: Custom barrel stand.
Posted: Mon Feb 16, 2015 4:21 pm
by AKweldshop
Bill Beauregard wrote:Have you considered adding four more pieces of angle to make it an octagon it sits on instead of a square, It would add strength.
That takes ability, out of my skill level....
RookieWelder wrote:Nicely done! Nothing wrong with that project that I can see.
Dwight
I sure hope not.
Re: Custom barrel stand.
Posted: Mon Feb 16, 2015 5:41 pm
by Braehill
John,
Outside of the obvious, what is the barrel stand's purpose? We can see it's to hold a barrel up, but why does it need to be raised? Is it a burn barrel and needs air to pass under, or for collecting rain water, or some other reason? Just curious.
Nice job by the way.
Len
Re: Custom barrel stand.
Posted: Mon Feb 16, 2015 6:02 pm
by AKweldshop
Braehill wrote:John,
Outside of the obvious, what is the barrel stand's purpose? We can see it's to hold a barrel up, but why does it need to be raised? Is it a burn barrel and needs air to pass under, or for collecting rain water, or some other reason? Just curious.
Nice job by the way.
Len
I think the guy will cut slots in the bottom for vents.
I'm not really sure.
It was just a quick fab job for a friend.
Re: Custom barrel stand.
Posted: Mon Feb 16, 2015 6:06 pm
by Braehill
I usually just cut holes in the bottom with an O/A torch and set a burn barrel up on a couple bricks, but the stand would work too.
Len
Re: Custom barrel stand.
Posted: Mon Feb 16, 2015 7:07 pm
by AKweldshop
Braehill wrote:I usually just cut holes in the bottom with an O/A torch and set a burn barrel up on a couple bricks, but the stand would work too.
Len
You can't weld bricks.....
