Page 1 of 1
Weld metal clutch repair.....
Posted: Wed Apr 16, 2014 2:04 am
by AKweldshop
Goes on a Oliver 770 farm tractor.
This clutch system was installed incorrectly by the mechanic before me....
you would push the clutch halfway down and it would disengage, push it to the floor, and it would engage again....
Instated backwards, loose bolts....
A mess, but, should be back and running by the end of the week.
Enjoy.
- IMG_1334.JPG (60.6 KiB) Viewed 1133 times
- IMG_1335.JPG (49.51 KiB) Viewed 1133 times
- IMG_1337.JPG (35.01 KiB) Viewed 1133 times
Re: Weld metal clutch repair.....
Posted: Wed Apr 16, 2014 2:12 am
by AKweldshop
- IMG_1340.JPG (61.3 KiB) Viewed 1132 times
- IMG_1569.JPG (85.21 KiB) Viewed 1132 times
- IMG_1570.JPG (87.23 KiB) Viewed 1132 times
Re: Weld metal clutch repair.....
Posted: Wed Apr 16, 2014 9:06 am
by ejpoter
You do get a lot of fun work. Would be nice if people would do it right the first time.
Sent from my DROID RAZR HD using Tapatalk
Re: Weld metal clutch repair.....
Posted: Wed Apr 16, 2014 10:43 am
by mcoe
I had to repair a clutch on an old Massey Ferguson 235. I was dragging the pasture and went to down shift before going down a steep hill and when I pushed the clutch pedal down it popped and the pedal went under the tractor and was gone. I shut the tractor down and got to looking and saw that I caught the bracket that holds the pedal to the tractor on a stump and broke it so I had to weld it back on the tractor. That was a fun drive back to the barn without a clutch.
Re: Weld metal clutch repair.....
Posted: Mon Oct 27, 2014 12:28 am
by AKweldshop
I just can't believe I never finished this thread!!
I did it all in one day, and got pics, but never posted them
I built the ears up with mig....and ground them all down to fit with like .030 tolerance...
And built the groves up on the housing sorta....(Third picture in this post
- IMG_1571.JPG (100.38 KiB) Viewed 849 times
- IMG_1572.JPG (66.16 KiB) Viewed 849 times
- IMG_1573.JPG (24.73 KiB) Viewed 849 times
Re: Weld metal clutch repair.....
Posted: Mon Oct 27, 2014 12:34 am
by AKweldshop
I wish I had better pics of the finished welds.
Sorry about that.
- IMG_1576.JPG (80.04 KiB) Viewed 849 times
- IMG_1587.JPG (49.11 KiB) Viewed 849 times
- IMG_1589.JPG (59.34 KiB) Viewed 849 times
Re: Weld metal clutch repair.....
Posted: Mon Oct 27, 2014 12:36 am
by AKweldshop
- IMG_1664.JPG (76.33 KiB) Viewed 848 times
Re: Weld metal clutch repair.....
Posted: Mon Oct 27, 2014 9:21 am
by rick9345
Now that is a repair well done
Re: Weld metal clutch repair.....
Posted: Mon Oct 27, 2014 2:44 pm
by AKweldshop
rick9345 wrote:Now that is a repair well done
Thanks!!
