Page 1 of 1
My homemade exhaust fan
Posted: Tue Jan 17, 2017 11:54 am
by electrode
I made this exhaust fan a some years ago using a Craftsman tool stand. I bought a squirrel cage blower off of ebay to make it functional. It was a 3 speed motor and I didn't have the controller so I did some research and fancy wiring with 3-way switches and got all 3 speeds to work. Really didn't need to do that because without the restriction of an air filter it in hardly noticeable.
Here it is:
![Dscf2827-a.jpg](./download/file.php?id=11454&sid=1488d36846283b9c2a83cd8d57f325d2)
- Dscf2827-a.jpg (33.46 KiB) Viewed 2187 times
Made from:
![spin_prod_209054601.jpg](./download/file.php?id=11455&sid=1488d36846283b9c2a83cd8d57f325d2)
- spin_prod_209054601.jpg (28.76 KiB) Viewed 2187 times
Re: My homemade exhaust fan
Posted: Tue Jan 17, 2017 1:17 pm
by homeboy
Very neat build. You cannot get too much ventilation in a shop. Lots of light -very important. Must have been interesting wireing the 3 speed switches.
![Smile :)](./images/smilies/icon_e_smile.gif)
Re: My homemade exhaust fan
Posted: Tue Jan 17, 2017 3:12 pm
by electrode
Thanks. On the wiring I had seen a video on Youtube where the guy did the same thing with a 3 speed motor but he didn't offer a schematic or instructions on how he wired it. I asked for a schematic but as usual, he never answered.
![Mad :x](./images/smilies/icon_mad.gif)
Of course I only waited an hour and went out and bought 3 of the 3-way switches and sat at the kitchen table with a multi-meter and figured it out. It really ended up pretty straight forward and easy. I made a drawing for future reference but don't know where I put it. That always happens when you put something in a really safe place.
![Mr. Green :mrgreen:](./images/smilies/icon_mrgreen.gif)
Re: My homemade exhaust fan
Posted: Tue Jan 17, 2017 6:05 pm
by doc58
That's a very neat and professional looking fan unit there.
Nice job.
Re: My homemade exhaust fan
Posted: Tue Jan 17, 2017 6:29 pm
by exnailpounder
Boom! I love it when people re-purpose things...Nice work!
Re: My homemade exhaust fan
Posted: Wed Jan 18, 2017 3:43 pm
by electrode
Thanks guys. It is nice to know some people appreciate other peoples handy work.
Re: My homemade exhaust fan
Posted: Wed Jan 18, 2017 8:53 pm
by homeboy
Actualy looks like something you could pick up at Ikea.
![Shocked :shock:](./images/smilies/icon_eek.gif)
Re: My homemade exhaust fan
Posted: Wed Jan 18, 2017 10:29 pm
by electrode
Re: My homemade exhaust fan
Posted: Wed Jan 18, 2017 10:45 pm
by Bumblebee
Nice build and if anyone need a drawing for 3 speed fan wiring contact me and I'll sure help you wire it up. Be sure and tell me voltage as a lot of HVAC fans are cap start and 220 volt to operate. The neat thing about them they can easily be between 800 to 1200 or more cfm if you can get the cage to. Contact any of the smaller HVAC contractors and as a rule they give or sell you one from the scrap file for low cost. I have a few so if you contact me just pay the shipping and ill send you one.
Re: My homemade exhaust fan
Posted: Mon Jan 30, 2017 11:53 pm
by pscampsr
It is very well done. You might think about using car door edge protector on the sharp edges. It cuts to length and just snaps on. Or poly-flow plastic tubing, slit it to slip over the edge. It is really tough (handles 5000 psi) and will give a nice round edge. Just a thought.
Re: My homemade exhaust fan
Posted: Tue Jan 31, 2017 11:21 am
by electrode
pscampsr wrote:It is very well done. You might think about using car door edge protector on the sharp edges. It cuts to length and just snaps on. Or poly-flow plastic tubing, slit it to slip over the edge. It is really tough (handles 5000 psi) and will give a nice round edge. Just a thought.
Thanks. I thought about edge protector but haven't got around to sourcing it. I guess Autozone may even sell it. I have slit tubing and rubber hose quite a few times like for making grommets for things etc but it is always tricky to do a long piece without bleeding or fighting the coil memory.
![Surprised :o](./images/smilies/icon_e_surprised.gif)
I will look into the door edge protector on this one.
![Smile :)](./images/smilies/icon_e_smile.gif)