[PhillerTime]

Built a welding cart in the ZT Fab style with a 12 gauge sheet 2'x4', left over 18 gauge 1" square tubing from a store display, and various lengths of 2", 3", and 4" .125 flat bar. I wanted the cart to hold two or more welders and two tanks. I found a barely used Lincoln 210mp on craigslist and had a lot of fun practicing mig. I used a plasma cutter to cut up the sheet metal parts.

tacked-up.jpg (61.89 KiB) Viewed 1748 times

I was so caught up on trying to make a good mig weld, I forgot about how much parts can and will warp. Really warped the sheet metal base when I fully welded (nonstop!) outside corner joints.

warped.jpg (58.84 KiB) Viewed 1748 times

I ended up trying to correct the 1/2" bow by clamping the base upside down to my downdraft table then fully welding the inside corner joints.

warped2.jpg (57.54 KiB) Viewed 1748 times

Now the base only kicks up about a 1/4" overall.

footpedal-fitup.jpg (32.86 KiB) Viewed 1748 times

I had fun bending the 4" x 1/8" flat stock with a small sledge-hammer and a wood vise.

finalassy.jpg (57.64 KiB) Viewed 1748 times

I bolted down 210mp via the factory holes inside the cabinet and made a little hook out angle iron to catch the lip of the Everlast 160STH.

leftview.jpg (79.1 KiB) Viewed 1748 times

rightview.jpg (81.39 KiB) Viewed 1748 times

rodholers-tanks.jpg (65.54 KiB) Viewed 1748 times

rearview2.jpg (62.15 KiB) Viewed 1748 times

The cart turned out bigger than I hoped but it's nice to have the control panel buttons a little higher than my last cart. Just want to say thank you to all the members, most posts are educational and often entertaining at the same time.

[homeboy]

Nice cart -lot of work but always worth it in the end. Had me going for a bit about why all the holes in the 1in tubes and then I went back and read your post and all was explained.

[PhillerTime]

Nice cart -lot of work but always worth it in the end. Had me going for a bit about why all the holes in the 1in tubes and then I went back and read your post and all was explained.

Yeah in retrospect, I should have just bought new steel.

[electrode]

Nice cart -lot of work but always worth it in the end. Had me going for a bit about why all the holes in the 1in tubes and then I went back and read your post and all was explained.

Yeah in retrospect, I should have just bought new steel.

Nothing wrong with re-purposing stuff. I do it all the time as do many others here. Looks like a lot of work went into that cart but it won't fall apart, that's for sure. Good job.

[PhillerTime]

Nice cart -lot of work but always worth it in the end. Had me going for a bit about why all the holes in the 1in tubes and then I went back and read your post and all was explained.

Yeah in retrospect, I should have just bought new steel.

Nothing wrong with re-purposing stuff. I do it all the time as do many others here. Looks like a lot of work went into that cart but it won't fall apart, that's for sure. Good job.

Thanks for the kind words!

[homeboy]

Actually I have quite a few projects with misc. holes and slots from reclaimed angle iron bed frames from the metal recycle pile at the landfill. If anyone asks what they're for just say -well isn't it obvious and change the subject.

[PhillerTime]

Actually I have quite a few projects with misc. holes and slots from reclaimed angle iron bed frames from the metal recycle pile at the landfill. If anyone asks what they're for just say -well isn't it obvious and change the subject.

Really lol! I'm going to use that one.