I spent probably 3 hours total on this. I guess someone who knew what they were doing could have it done in a little over an hour. To match the round tubing contour to the square tubing I traced the contour with a scribe, cut slots with a cutoff wheel up to the scribe mark, then ground I all out with a grinding wheel and ground a little here and there till it made a good fit. I realized later I could have cut a thin piece off the round tubing to use as a guide for the plasma cutter and saved a lot of time. I had a hard time getting everything fit up perfectly and it is still a tiny bit out of square. I originally thought I might tig weld it up since I like tig welding so much, I am really glad I didn't. I was pretty happy with my weld job I did on this. The whole point to the contraption is to elevate the plates off the floor, that way they can easily be slid on or off. Before I would roll it onto a 5 pound plate. This is a ton simpler.
- Attachments
-
- DSC08019.JPG (50.96 KiB) Viewed 1799 times
-
- DSC08018.JPG (39.05 KiB) Viewed 1799 times
-
- DSC08017.JPG (28.58 KiB) Viewed 1799 times
-
- With 450 pounds on the end of the bar, it still moves it easily enough.
- DSC08016.JPG (45.78 KiB) Viewed 1799 times
-
- DSC08015.JPG (52.48 KiB) Viewed 1799 times
-
- DSC08014.JPG (55.81 KiB) Viewed 1799 times
- weldin mike 27
-
Weldmonger
-
Posts:
-
Joined:Fri Apr 01, 2011 10:59 pm
-
Location:Australia; Victoria
Good stuff. It would probably have taken me three hours or more as well, and I'm a tradesman. Keep up the good work. Ps most people who mouth off about how fast they are are usually rubbish.
- Braehill
-
Weldmonger
-
Posts:
-
Joined:Sat Jul 06, 2013 11:16 am
-
Location:Near Pittsburgh,Pennsylvania. Steel Buckle of the Rust Belt
Butcher,
If you're deadlifting 900# then you don't need to care what others think about how fast you got it done.
Nice work and as the other's have said, fit up makes life a lot easier.
If you have a drill press and a hole saw the same size as the pipe, square tubing is very easy to cope. You can even do 2 copes at once if you plan it right by drilling with the hole saw where the 2 coped ends meet.
Len
If you're deadlifting 900# then you don't need to care what others think about how fast you got it done.
Nice work and as the other's have said, fit up makes life a lot easier.If you have a drill press and a hole saw the same size as the pipe, square tubing is very easy to cope. You can even do 2 copes at once if you plan it right by drilling with the hole saw where the 2 coped ends meet.
Len
Now go melt something.
Instagram @lenny_gforce
Len
Instagram @lenny_gforce
Len
- TRACKRANGER
-
Weldmonger
-
Posts:
-
Joined:Wed Aug 06, 2014 12:48 am
-
Location:Melbourne, Australia
Great effort, you'd be pretty pleased with your results.
Trevor
Trevor
EWM Phonenix 355 Pulse MIG set mainly for Aluminum, CIGWeld 300Amp AC/DC TIG, TRANSMIG S3C 300 Amp MIG, etc, etc
Haha, I'm not deadlifting 900! I just wanted to see how easily the jack would move a loaded bar and I couldn't fit any more than 10 plates on the end.Braehill wrote:If you're deadlifting 900# then you don't need to care what others think about how fast you got it done.