Welding Tips and Tricks

Anyone know of a place hiring for a welder in the New Orleans area , Slidell , Covington . Tig ,stick,mig also aluminum and stainless . Anything will help thanks

While I don't see welding positions on their website at the moment, I'd put a resume' in at MECO,

http://www.meco.com/about-meco/employment

They pay well and seem to have a good work environment.

Also try Phoenix Energy Services, on 190 in Goodbee, a half-mile east of 1077.

I'll ask around on Monday, and might be able to give you a few that are known to be hiring.

Steve S

Thanks a lot. I'll check into them

Maybe it's just me , but I can't find anything on Phoenix energy services in goodbee. Anyone know of a good number or website ?

duckhunter27 wrote:Maybe it's just me , but I can't find anything on Phoenix energy services in goodbee. Anyone know of a good number or website ?

I drive by it often.

My search for a website or # came up blank, also.

I'll take a closer look tomorrow.

Steve S

Sorry if this is short notice (I got this yesterday, myself):

CB&I Open House – Screening for Shop Pipe Welders

Position: Shop Pipe Welders

This is not a Field position. This position does not offer per diem.

Minimum Requirements: Must be able to Tig, Mig, & Stick on Pipe.

Wednesday, April 20th, 2016

08:00 a.m. to 02:00 p.m.

Location:

29684 South Frost Road

Livingston, LA 70754



No Appointment Necessary.

Bring Resume or a list of Employment History and Qualifications.

PPE Required: long sleeve shirt, long pants, and steel toe leather boots (above ankle).

Qualified candidates will be required to complete a brief hands-on skills test at a secondary location.

Directions:

From Florida Blvd (Hwy 190):

Travel 4.8 miles and turn right onto S. Frost Road (red light in Livingston)

Location is a ½ mile on the left.

Training facility in Plaza 63 to the right of Carter’s Supermarket.

The CB&I Training Facility is the 4th building from the front of the building.



From I-12:

Take Exit 22 onto Hwy 63 in Livingston.

Travel North on South Frost Road

Location is 1.3 miles on the right.

Training facility in Plaza 63 to the right of Carter’s Supermarket.

The CB&I Training Facility is the 4th building from the front of the building.

There is now a job available in Slidell.

The company is Elite Cryogenics, and is where I work.

They have opted to hire through a staffing agency, "Treo", but if you have the right qualifications I might be able to get you a direct-hire interview.

The most basic requirements are TIG on SS pipe, and MIG on carbon/stainless structure, and mechanical aptitude.
Additional skills that will make a standout candidate include pipefitting, fabrication, instrument fitting, and electrical. Not all (or any) are required, but each is a plus.

Steve

Otto Nobedder wrote:There is now a job available in Slidell.

The company is Elite Cryogenics, and is where I work.

They have opted to hire through a staffing agency, "Treo", but if you have the right qualifications I might be able to get you a direct-hire interview.

The most basic requirements are TIG on SS pipe, and MIG on carbon/stainless structure, and mechanical aptitude.
Additional skills that will make a standout candidate include pipefitting, fabrication, instrument fitting, and electrical. Not all (or any) are required, but each is a plus.

Steve

Where, when and who do I contact?

Otto Nobedder wrote:There is now a job available in Slidell.

The company is Elite Cryogenics, and is where I work.

They have opted to hire through a staffing agency, "Treo", but if you have the right qualifications I might be able to get you a direct-hire interview.

The most basic requirements are TIG on SS pipe, and MIG on carbon/stainless structure, and mechanical aptitude.
Additional skills that will make a standout candidate include pipefitting, fabrication, instrument fitting, and electrical. Not all (or any) are required, but each is a plus.

Steve

Can I send you my resume , I will contact treo . I have plenty experiment on as pipe and mig on carbon and stainless . I've done some pipe fitting and plenty of general fabrication . Thanks for the heads up

Those are some good pictures.
I e-mailed you the contact information.

Steve S