Tig welding tips, questions, equipment, applications, instructions, techniques, tig welding machines, troubleshooting tig welding process
The what I welded today (/whenever) thread (pics please)
Post Reply
Coldman
  • Posts:
  • Joined:
    Mon Dec 15, 2014 2:16 am
  • Location:
    Oz

Had to chop out a couple of 3" refrigeration ammonia stop valves and replace with stop/check valves.
v2.jpg
v2.jpg (50.88 KiB) Viewed 2251 times
The replacement valves were shorter in both dimensions so the first job was to weld on pups.
v1.jpg
v1.jpg (42.11 KiB) Viewed 2251 times
Left hand valve welded in.
v3.jpg
v3.jpg (54.26 KiB) Viewed 2251 times
Setting right hand valve in position and adjusting gap.
v4.jpg
v4.jpg (61.41 KiB) Viewed 2251 times
All welded out.
v5.jpg
v5.jpg (48.27 KiB) Viewed 2251 times
v6.jpg
v6.jpg (48.67 KiB) Viewed 2251 times
v7.jpg
v7.jpg (64.04 KiB) Viewed 2251 times
Flat out like a lizard drinkin'
Top
Poland308
  • Posts:
  • Joined:
    Thu Sep 10, 2015 8:45 pm
  • Location:
    Iowa

Nice job on the valves.
I have more questions than answers

Josh
Top
User avatar
  • Posts:
  • Joined:
    Sun Jan 27, 2013 6:23 am
  • Location:
    Finland

I'm not a big fan of heat tint colors, but sometimes those are fun to watch :D

316L 21,3x1,6 mm pipe.
Attachments
WP_20150914_15_06_10_Pro.jpg
WP_20150914_15_06_10_Pro.jpg (24.24 KiB) Viewed 2211 times
-Markus-
Top
User avatar
  • Posts:
  • Joined:
    Fri Apr 01, 2011 10:59 pm
  • Location:
    Australia; Victoria

Cold man, What must one do before welding on a system that has contained ammonia?

Mick
Top
Rick_H
  • Posts:
  • Joined:
    Sat Feb 08, 2014 1:50 pm
  • Location:
    PA/MD

Nice Markus was that machine or hand?
I weld stainless, stainless and more stainless...Food Industry, sanitary process piping, vessels, whatever is needed, I like to make stuff.
ASME IX, AWS 17.1, D1.1
Instagram #RNHFAB
Top
Coldman
  • Posts:
  • Joined:
    Mon Dec 15, 2014 2:16 am
  • Location:
    Oz

If welding on a vessel we purge for 10min with nitrogen. If pipework first we pump it down to a bit of vacuum then break with air and get into it. If there is oil present (often) it will have disolved ammonia which gases out into the weld and welder. This is where inexperienced welders put on their skirts and run away screeming. I've been sucking it for 35 years as a fridgy and since I've been welding I get calls from all over for crap jobs nobody wants to touch. Is this a niche? Anyway you don't want ammonia in your welds. This happens when valves don't hold - it happens. The arc and gas shield glows green like the hulk, the tungsten starts to disappear and you get severe porosity in your weld. Alot of cursing happens about this time. To seal off a butt we weld a socket on the pipe upstream from the joint to let pressure and flow out while we complete the butt and then screw a plug or valve into the socket.
I watched a mate of mine weld a 12" leg into the underside of a horizontal vessel with oil and ammonia running out through the joint. He used 5p for root and 7016 out. That joint got xray ultrasonic and mag particle and passed all. Awesome job. Gobsmacked.
Flat out like a lizard drinkin'
Top
User avatar
  • Posts:
  • Joined:
    Sun Jan 27, 2013 6:23 am
  • Location:
    Finland

Rick_H wrote:Nice Markus was that machine or hand?
Thanks Rick. That one was hand welded this time. 2mm is much harder to get same colors due to heat.
-Markus-
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 24, 2013 6:44 am

Starting a new batch of frames.
IMG_20150915_171550.jpg
IMG_20150915_171550.jpg (46.03 KiB) Viewed 2073 times
IMG_20150915_171246.jpg
IMG_20150915_171246.jpg (37.01 KiB) Viewed 2073 times
Top
User avatar
  • Posts:
  • Joined:
    Sat Aug 01, 2015 8:38 am
  • Location:
    The Land Down Under

Love your work, Zank.



Kym
Top
User avatar
  • Posts:
  • Joined:
    Fri Apr 01, 2011 10:59 pm
  • Location:
    Australia; Victoria

Thanks coldy. If my current job goes tits up (possible) im heading straight to our local Refrigeration company, that does welded systems.

Mick
Top
Coldman
  • Posts:
  • Joined:
    Mon Dec 15, 2014 2:16 am
  • Location:
    Oz

That would be gbi?
Flat out like a lizard drinkin'
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 24, 2013 6:44 am

MosquitoMoto wrote:Love your work, Zank.



Kym
Thanks, Kym!
Top
User avatar
  • Posts:
  • Joined:
    Wed Aug 06, 2014 12:48 am
  • Location:
    Melbourne, Australia

KYNgsx

Welcome to the Forum

Tell us a bit about yourself in Member Introductions if you like.

Neat work too!

Trev
EWM Phonenix 355 Pulse MIG set mainly for Aluminum, CIGWeld 300Amp AC/DC TIG, TRANSMIG S3C 300 Amp MIG, etc, etc
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 24, 2013 6:44 am

Last ones for this week.
Image
Chip B by Mike Zanconato, on Flickr

Image
Chip B by Mike Zanconato, on Flickr

Image
Chip B by Mike Zanconato, on Flickr
Top
User avatar
  • Posts:
  • Joined:
    Sun Sep 22, 2013 10:14 am
  • Location:
    Minneapolis Mn 55407

I am crying in my cups!
Everlast 250EX
Miller 250 syncrowave
Sharp LMV Vertical Mill
Takisawa TSL-800-D Lathe
Coupla Bandsaws,Grinders,surface grinder,tool/cutter grinder
and more stuff than I deserve(Thanks Significant Other)
Top
User avatar
  • Posts:
  • Joined:
    Sat Aug 01, 2015 8:38 am
  • Location:
    The Land Down Under

zank wrote:Last ones for this week.
Image
Chip B by Mike Zanconato, on Flickr

Image
Chip B by Mike Zanconato, on Flickr

Image
Chip B by Mike Zanconato, on Flickr
Pure weldporn.


Kym
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 06, 2011 11:40 pm
  • Location:
    Near New Orleans

Nice work, as usual, Zank!

Nothing special here... I am trying out a new camera. It's a bit of a cheapie, but it doesn't have 30 features I'll never use.

Just some basic pipe fab. First pic in standard mode, second in "macro" for close-ups. We'll see how they come through on the forum.

Steve S
DSCF0002.JPG
DSCF0002.JPG (118.65 KiB) Viewed 2096 times
DSCF0005.JPG
DSCF0005.JPG (73.69 KiB) Viewed 2096 times
Top
Poland308
  • Posts:
  • Joined:
    Thu Sep 10, 2015 8:45 pm
  • Location:
    Iowa

are those some sort of vac regulators?
I have more questions than answers

Josh
Top
User avatar
  • Posts:
  • Joined:
    Sat Jul 06, 2013 11:16 am
  • Location:
    Near Pittsburgh,Pennsylvania. Steel Buckle of the Rust Belt

They're pressure relief valves (safeties) on a liquid Hydrogen trailer.

Len
Now go melt something.
Instagram @lenny_gforce

Len
Top
Poland308
  • Posts:
  • Joined:
    Thu Sep 10, 2015 8:45 pm
  • Location:
    Iowa

Like on a semi trailer or a skid for set up somewhere?
I have more questions than answers

Josh
Top
User avatar
  • Posts:
  • Joined:
    Sat Jul 06, 2013 11:16 am
  • Location:
    Near Pittsburgh,Pennsylvania. Steel Buckle of the Rust Belt

Semi trailer, but they're also used on the stationary tanks that they deliver to.

Len
Now go melt something.
Instagram @lenny_gforce

Len
Top
Rick_H
  • Posts:
  • Joined:
    Sat Feb 08, 2014 1:50 pm
  • Location:
    PA/MD

The temps like to steal the sanitation tooling we have at the lines so I fabbed up a lockable holder..of course in stainless.
Attachments
IMG_20150917_214617867.jpg
IMG_20150917_214617867.jpg (34.54 KiB) Viewed 2240 times
IMG_20150917_214607803.jpg
IMG_20150917_214607803.jpg (33.92 KiB) Viewed 2240 times
Last edited by Rick_H on Sat Sep 19, 2015 11:18 pm, edited 1 time in total.
I weld stainless, stainless and more stainless...Food Industry, sanitary process piping, vessels, whatever is needed, I like to make stuff.
ASME IX, AWS 17.1, D1.1
Instagram #RNHFAB
Top
User avatar
  • Posts:
  • Joined:
    Wed Aug 06, 2014 12:48 am
  • Location:
    Melbourne, Australia

Good one Rick. Does the job nicely!
EWM Phonenix 355 Pulse MIG set mainly for Aluminum, CIGWeld 300Amp AC/DC TIG, TRANSMIG S3C 300 Amp MIG, etc, etc
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 06, 2011 11:40 pm
  • Location:
    Near New Orleans

Poland308 wrote:Like on a semi trailer or a skid for set up somewhere?
Semi trailer.

I knew Len would recognize them...

Steve S
Top
Poland308
  • Posts:
  • Joined:
    Thu Sep 10, 2015 8:45 pm
  • Location:
    Iowa

Cool always like to learn a little more.
I have more questions than answers

Josh
Top
Post Reply

Return to “Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding”