[Rick_H]

Nice repair....you ever wonder what the hell some people are thinking when you run across that crap.

[GreinTime]

Looks good! I was showing my son how to tig and he moved in to look and stood on the hose. Felt pretty foolish toasting a tungsten with him looking while I'm bragging about how good I am

I fucking gassed myself twice last night with my stool at work lol

Sent from my SM-G900V using Tapatalk

[Coldman]

A blind man on a galloping horse would be pleased to see that.

[exnailpounder]

Looks good! I was showing my son how to tig and he moved in to look and stood on the hose. Felt pretty foolish toasting a tungsten with him looking while I'm bragging about how good I am

I fucking gassed myself twice last night with my stool at work lol

Sent from my SM-G900V using Tapatalk

I always let out a little "test fart" before I unload completely. Some stool is worse than others

[GreinTime]

Looks good! I was showing my son how to tig and he moved in to look and stood on the hose. Felt pretty foolish toasting a tungsten with him looking while I'm bragging about how good I am

I fucking gassed myself twice last night with my stool at work lol

Sent from my SM-G900V using Tapatalk

I always let out a little "test fart" before I unload completely. Some stool is worse than others

I just snorted lol

Sent from my SM-G900V using Tapatalk

[cb400chopper]

A weld off the gate I made for my yard and the gate all finished


Sent from my HTC_PN071 using Tapatalk

[LtBadd]

A weld off the gate I made for my yard and the gate all finished


Sent from my HTC_PN071 using Tapatalk

Nice fab and welding chopper!

[cb400chopper]

Thanks a lot being trying to get my skills back to when I did it for a living a few years ago. Another project I built recently was this table, welds wernt as good but getting better every time

Sent from my HTC_PN071 using Tapatalk

[Rick_H]

You guessed it more stainless....lol Started a new frame for a machine guard.

[cb400chopper]

Nice welds and a very nice bench

Sent from my HTC_PN071 using Tapatalk

[Rick_H]

Update..

[Coldman]

Are you sure that's a machine guard? I recon it would make a bonza dunny too.
Even the emus couldn't kick that one down!

[GreinTime]

A few different welds from work today, compliments of an Instagram widget for putting them together in a collage! @greintime3592 if any of you are on there

Sent from my SM-G900V using Tapatalk

[Coldman]

I'm crazy huh. I see welds like that and get a tingling in the loins.

[fredygump]

Today I was using an old Esab welder; they said it was "touchy". It was fine all morning, but when I came back from lunch it abruptly started malfunctioning. It would "Pop" every time I tried to start a weld, and the actual volts and amps on the machine were all over the place. I asked for 18v, and it gave me 20, or 30 or 50.

I decided to throw in the towel when it liquified the contact tip, rather, the first time it liquified a contact tip. I told the boss, and all the guys came over, thinking that they could fiddle with the settings and get it to work right. One guy kept trying to get the thing to weld, until suddenly, "KABLAMMOOO!" Actually, a ridiculously bright flash and a sound something like a plasma torch for a fraction of a second. Immediately afterward the machine registered 60v and 450A! The picture is the aftermath of this decisive event. If you look closely, you'll notice that 1/8" of the end of the contact tip is missing. The lump of metal you see directly under the tip in the photo is the missing part of the contact tip.

The welder itself didn't blow up, so it must be a control board that's fried? My boss decided it would be a good idea to have a service tech look at it.

The machine is a CC/CV transformer machine, like the Warrior model. It is an older machine, and I don't know what model it is.

[GreinTime]

I'm crazy huh. I see welds like that and get a tingling in the loins.

My loins have been tingling since I laid them, but I think that may be something else!

Sent from my SM-G900V using Tapatalk

[zank]

Some stuff from the past couple of weeks.


dip dip dip by Mike Zanconato, on Flickr


Jared B by Mike Zanconato, on Flickr


Stephen V by Mike Zanconato, on Flickr


Stephen V by Mike Zanconato, on Flickr

Pete S by Mike Zanconato, on Flickr


ready to race? by Mike Zanconato, on Flickr

[Rick_H]

Stainless machine guard

The one photo shows a little fixture I use when mounting hinges, use a small piece of angle above to quickly locate where it should be, stays square too.

[LS Customs]

finished welding up and painted cart for tig machine and cooler...

[Fe3c]

On a whim I decided to make my parts car widebody. I have 0 experience with body work. I have about 1 experience welding.
I figured what could go wrong? I am pleased thus far.

[ex framie]

That pressure you feel on the end of your nose is the verticle learning curve you've just hit.
Man are you going to learn a lot on this one.
And probably a few new words
Remove all dirt /grease/paint back to clean bare metal where you want to weld, keep the earth close to the weld (also on clean bare metal).
Tack, tack, tack, then stitch weld, moving around to spread the heat and hopefully lessen distortion
Watch Jodies vids.
Keep the photos comming.
Mig or Tig?

Cheers

[Fe3c]

Thanks to the square nature of the car, it's going pretty smoothly. I have about 3 hours into it and have gotten it this far.
I'm absolutely loving it. I so wish I had gotten into welding at 18 instead of 33.

[dmcnally]

I didn't weld anything. I've been planning on building a welding cart, but I haven't finalized on the exact design (i.e. paralysis by analysis). The local school district is going to tear down a derelict high school and they had a whole bunch of cr@p on the lawn waiting to be thrown into roll-off dumpsters. I decided to look through it and rescue a few items.

I grabbed 7 AV carts and hauled them home.

100_2449.JPG (63.04 KiB) Viewed 2111 times

I decided to use one of them as a welding cart while I hem and haw over my design for a welding cart.

100_2451.JPG (59.23 KiB) Viewed 2111 times

100_2452.JPG (61.32 KiB) Viewed 2111 times

Dave

[Rick_H]

Busy week was finally able to get back to my guard, no welding but lots of fab work. Lexan doors, flush mount stainless handles, magnetic catches, LED lights and tomorrow weld tabs in and install door locks/latches. (Everything must require a tool to open door per regulations) Amazing how long all that stuff takes....lol

[Charlie337]

I think a tight fitting miter is always sexy