Tig welding tips, questions, equipment, applications, instructions, techniques, tig welding machines, troubleshooting tig welding process
Foot Pedal vs Hand switch? (walking the cup)
Post Reply
crouchy
  • Posts:
  • Joined:
    Sat May 23, 2015 4:18 am
  • Location:
    worthing, England

Hi guys,

Im getting practice in on 6g test (63mm carbon steel 6mm wall) just wondered if you guys used the foot pedal or the hand switch? Or is it a case of whats comftable for you?
Top
User avatar
  • Posts:
  • Joined:
    Wed Aug 06, 2014 12:48 am
  • Location:
    Melbourne, Australia

crouchy wrote:Hi guys,

Im getting practice in on 6g test (63mm carbon steel 6mm wall) just wondered if you guys used the foot pedal or the hand switch? Or is it a case of whats comftable for you?
I started off with hand switch (2T 4T). My torch even has thumb-wheel control. Moved to a foot-pedal, much better control. YMMV but for me, I never looked back.
EWM Phonenix 355 Pulse MIG set mainly for Aluminum, CIGWeld 300Amp AC/DC TIG, TRANSMIG S3C 300 Amp MIG, etc, etc
Top
Coldman
  • Posts:
  • Joined:
    Mon Dec 15, 2014 2:16 am
  • Location:
    Oz

It depends on what you are aiming to do. If you are going to be spooling in a workshop, the pedal is ideal. If you're going to be in field doing pipework you may as well get used to a torch switch now while you're practicing cause the pedal is of little use out there.
Flat out like a lizard drinkin'
Top
crouchy
  • Posts:
  • Joined:
    Sat May 23, 2015 4:18 am
  • Location:
    worthing, England

Thanks guys, will punt the hand switch back and practice using that. Thumb wheel control you say? What make of touch do you have trackranger??
Top
taz
  • Posts:
  • Joined:
    Mon May 26, 2014 12:43 pm
  • Location:
    Athens - Greece

I use a hand switch or even scratch start for all my steel pipe welding. The only time I will use a pedal welding pipe is for aluminum or on the bench.
Top
User avatar
  • Posts:
  • Joined:
    Wed Aug 06, 2014 12:48 am
  • Location:
    Melbourne, Australia

crouchy wrote:Thanks guys, will punt the hand switch back and practice using that. Thumb wheel control you say? What make of touch do you have trackranger??
I should have clarified. The torch switch is absolutely fine. The thumb-wheel control compared to foot-pedal control is where the foot pedal is much easier. Again, it depends if you're sitting at a bench or standing. Foot-pedals are quite difficult to use unless you are seated.

I'll try and get a photo of the torch later today
EWM Phonenix 355 Pulse MIG set mainly for Aluminum, CIGWeld 300Amp AC/DC TIG, TRANSMIG S3C 300 Amp MIG, etc, etc
Top
User avatar
  • Posts:
  • Joined:
    Wed Aug 06, 2014 12:48 am
  • Location:
    Melbourne, Australia

Here it is:
Attachments
TIG torch.jpg
TIG torch.jpg (41.62 KiB) Viewed 1011 times
EWM Phonenix 355 Pulse MIG set mainly for Aluminum, CIGWeld 300Amp AC/DC TIG, TRANSMIG S3C 300 Amp MIG, etc, etc
Top
plain ol Bill
  • Posts:
  • Joined:
    Wed Apr 08, 2015 6:46 pm
  • Location:
    Tenino, WA

The only TIG torches I ever saw on the jobs were dry rigs running off the same power source for stick machines. If you were really lucky you might have a remote amperage control but most of the time you set your amperage close and lived with what you had rather than crawl out of the boiler and adjust and crawl back in several times. If you were really lucky you could run a long ground lead to the work and swap polarity by switching leads for stick welding. Contractors just won't spend the money for the nice stuff if you can get by with less.
Tired old welder
CNC plasma cutter
Colorful shop w/
Red, blue, yellow, purple, and Hypertherm silver equip.
Top
Post Reply

Return to “Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding”