What I welded today, stick section!

DennisZ · Sun Mar 01, 2015 7:28 am

I like the "what I welded today" thread in the TIG and MIG section. Are you guys afraid to show off your stick welds?? Or is it that stick welds usually are less interesting projects? By that I mean, I don't see ZANK weld his quality stuff with stick...

I am not going to start off with pictures of my projects just because I don't have any pictures from them....

AKweldshop · Sun Mar 01, 2015 1:40 pm

You've got my vote !!

DennisZ · Sun Mar 01, 2015 2:31 pm

AKweldshop wrote:You've got my vote !!

Well you're one with a lot of welding projects, care to show some?

AKweldshop · Sun Mar 01, 2015 2:43 pm

No problem,
Give me a few mins.

: image.jpg (43.11 KiB) Viewed 3578 times

DennisZ · Sun Mar 01, 2015 2:45 pm

Yep that's the way I like to see my welds! (Don't always succeed though)

Svetsare · Sun Mar 01, 2015 3:34 pm

Well here is some pics if you are interested.

Only stainless weld in my computer now.. sorry for that.

Svetsare · Sun Mar 01, 2015 3:35 pm

AKweldshop wrote:No problem,
Give me a few mins.

image.jpg

Nice work : ) 7024 or what?

Ratsathome · Sun Mar 01, 2015 4:33 pm

My once off as well

Builded Friday a swivel stand for my drill press and band saw. No pics yet. Will update Monday.
Better have it and not use it than need it and don't have it.

DennisZ · Sun Mar 01, 2015 4:44 pm

Since there's no "LIKE" button here....

when you make its maiden run you give me a call Ok?

[img]

: IMG-20150204-WA0002.jpg (71.17 KiB) Viewed 3564 times

[/img]

AKweldshop · Sun Mar 01, 2015 5:16 pm

Svetsare wrote:
AKweldshop wrote:No problem,
Give me a few mins.

image.jpg
Nice work : ) 7024 or what?

1/8" 7018 at 135amps.

AKweldshop · Sun Mar 01, 2015 6:33 pm

Here's some vertical up 1/8" 7018.
115amps.

AKweldshop · Sun Mar 01, 2015 7:29 pm

1g smaw.....1/8' 7018 135amps.

: IMG_2442.JPG (58.45 KiB) Viewed 1688 times

Ratsathome · Thu Mar 05, 2015 9:30 am

So I changed again my mind and put my chop saw with my drill press on the swivel table.
Maybe not the most efficient way to do it but with limited space it works for me.

Why would I buy a thing for a tenner if I can make it for fifty.

motox · Thu Mar 05, 2015 12:09 pm

nice
simple and funtional
craig

DennisZ · Tue Mar 17, 2015 3:30 pm

No weld pics but here is one of my biggest projects I ever welded. Needed a place to store the feeds for our cows (I am a dairy farmer). Before we received a factory made mix that we would unload underneath a low roof so the truck had to tip outside and we had to push the product in with a wheel loader.

We had a whole bunch of galvanised steel from various sizes laying around from a previous barn build. Some pieces were obsolete others got replaced (the building came down when it was in first stage of erecting it)

So we decided we could build a new building so that we could buy single products in full truckloads. Made a list of the beams we had and I drew out a design on a piece of paper. Biggest challenge was the floor had allready been poured years before, but had slopes to various sides. So columns had to be different lengths. Plus being different sizes it was quite some calculating. Cut them all to length, welded plates on them with holes so it could be bolted in place. Quite a project for a first time...

But it all fit perfectly together when we put it up. Roof and walls are new steel, and the horizontal profiles supporting the roof sheets are also new. Rest is all used. dimensions are 10 meter high on the front 17 meter wide and about 16 meter deep.

Tue Mar 17, 2015 7:48 pm

Here's a 6010 root (no roll-out), done on sch. 80 carbon, 12", if I recall. Buffed it, because it didn't show at all otherwise.

: 6010 root.jpg (40.66 KiB) Viewed 1612 times

Steve S

Tue Mar 17, 2015 7:59 pm

Here's two more of the same blind leg I was building for hydro-testing a steam system.

: GEDC0245.JPG (47.57 KiB) Viewed 1608 times

: GEDC0250.JPG (48.64 KiB) Viewed 1608 times

Been a while...

Steve S

Tue Mar 17, 2015 8:03 pm

I think this is a good idea, and I think I'll rename the topic accordingly, unless the OP objects.

[EDIT] That was easy! Two bits of punctuation, and done!

Note it only changed in the main page heading, not the individual posts since this began.

Steve S

Tue Mar 17, 2015 8:08 pm

Test message, to see if my header changed.

[EDIT] It did!

Steve S

Tue Mar 17, 2015 8:10 pm

Good idea, DennisZ!

Steve S

DennisZ · Wed Mar 18, 2015 3:16 am

Thanks Steve.

Nice job.

AKweldshop · Wed Mar 18, 2015 11:55 am

I got to do some welding for a few hours last night, demoing the new pm210mp.
Did some 3g filling on 3/4" plate.

Superiorwelding · Wed Mar 18, 2015 12:55 pm

Looking good John. How does that machine run compared to other Lincoln models? What about compared to Everlast?
-Jonathan

AKweldshop · Wed Mar 18, 2015 1:11 pm

Superiorwelding wrote:Looking good John. How does that machine run compared to other Lincoln models? What about compared to Everlast?
-Jonathan

They all weld similar.....I honestly couldn't tell much difference between all my Lincolns.
Everlast machines weld 7018 just as nice.....

Boomer63 · Wed Mar 18, 2015 1:27 pm