[rahtreelimbs]

For cutting and heating ( Rosebud tip ) what settings are required on the regulators?

[jpence38]

Check this out. Hope it helps.

scan0001.jpg (104.94 KiB) Viewed 6594 times

[anthonyfawley]

set the oxy @ 35-40 psi and the acetaline at 7-10 psi and you should be good for most applications.

[Tom O]

The manufacturer of your torch has charts for type of tip and their proper pressures. Contact them or go online for their charts.

[Tim]

A rosebud tip is a heating tip that you use for making a low temp solder joint - copper water pipe, air conditioning pipe. its not a cutting tip. Rosebud tips for oxy/acet torches are operated with acetalene only and get their oxygen from the atmosphere. Or, you can get a rosebud specific soldering handpiece for $25 that operates with MAPP or propane ... and you get a soft, low temp flame which is perfect for soldering a copper pipe.

Cutting requires 40psi oxygen to firstly superheat the metal and secondly to blow it physically out of the way. Kinda like a plasma cutter that uses high pressure compressed air. If you add oxygen to a rosebud tip, you will melt the tip off.

[jpence38]

Tim,
Don't want to offend you, but the info you provided is not accurate. You should check into the subject a little more.

[ogorir]

Jim, I think tim is only wrong in name. I think Tim is talking about the slip-on tips made for body soldering and light heating applications. I've heard them called rosebuds (they're not.) before and they are an acetylene-air device and you will pop the tip off the end if you add in oxy. I can't seem to find a picture 'cause I don't actually know their proper name, but theres a brass ferrule with a rubber gasket that slips over a standard welding tip and in the ferrule around the tip there are air inlet holes so the flame can draw air and create turbulence. I think the body on the one my grandpa has is rubber, then it goes to a fairly wide opening tip.

basically, it's just converting your oxy/acetylene rig into a plumbers-style air-fuel torch without changing tips. they work good for what it's worth, but its a hell of a lot cheaper to just use the plumbers torch.

[jpence38]

Ogorir,
That makes a little more sense. Have never heard of that kind of heating tip before. Thanks

[Tim]

Tim,
Don't want to offend you, but the info you provided is not accurate. You should check into the subject a little more.

Jim, well it is offensive when you say someone is wrong without saying why. That is just plain ignorant. I'm talking about a turbo torch kinda thing for solder joints. If thats not what you're talking about, then your question was just too vague. Sorry to bother you.

[jpence38]

Tim,
First of all, I didn't ask a question. I answered the original post's question about cutting and heating settings on regulators. He didn't want to know what a rosebud was and nothing was even mentioned about soldering. I can certainly understand wanting to help someone, but if you are not sure about your information then you really should not answer a question. Your information was WRONG for what the question was asking. And you don't bother me.

[jwmacawful]

where i come from (n.y.c.) a rosebud is an oxy~acetylene tip or attachment that's used to pre-heat weld joints or heating material prior to bending or forging. the air only torch used in sweating plumbing and/or refrigeration lines is called a turbo torch. for general burning (up to 5" thick)and (rosebud) heating i set the oxygen regulator to 40psi and the acetelene to 10psi. for brazing and silver soldering i reduce these settings by half, 20 and 5psi. there is a large propane heating torch used in roofing and general heating jobs that's also called a rosebud. yeah, it's confusing isn't it?

[welder57]

i set mine at 40# oxy and 5-7# for general cutting. i found that dropping the oxy to 20# for rosebud operation works well. the setting is usually indicative of the btu rating of the tip. the torch manu. should be helpful like the chart i just saw

[rickbreezy]

"oh no you did'nt!!"

haha.