Ideas & suggestions for videos
I would like to see a video from Jody on how the volt/amp controls work on a Lincoln SA200. The whole volt/amp curve thing can be confusing and I'm sure Jody will do a great job as always in making it clear for all.
Steve
1966 Lincoln SA200 Redface
1990 Miller Dialarc 250
2003 Miller Maxstar STR
2015 Lincoln MP210
Victor & MECO torches
1966 Lincoln SA200 Redface
1990 Miller Dialarc 250
2003 Miller Maxstar STR
2015 Lincoln MP210
Victor & MECO torches
Looking for good deals in Welding Supplies
Bill Beauregard
- Bill Beauregard
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 9:32 pm
-
Location:Green Mountains of Vermont
Travis Field, fieldres on you tube did a video on the subject. Steel melts because of the heat generated by a high resistance ionized gas and the arc of electrons flowing across. Electrical power is measured in watts. Electrical pressure is measured in volts. volume is measured in amperes. Volts x amps is watts. 10 volts x 100 amps is 1000 watts. 100 volts x 10 amps is 1000 watts. The energy is equivalent. In vertical welding if we produce the wattage with lower voltage, and higher amperage, we can drag the rod, or even push it directly into the joint to burn deep pockets in the cooler workpiece. The molten metal surrounded by cooler steel freezes very quickly, preventing drips.
Conversely, higher volts, lower amps will tend to snuff out the arc if held too close. the longer arc needed will tend to melt less deeply into the workpiece. Less contact with cooler steel means slower cooling of molten filler metal.
Other situations like thin metal laid flat work well with more voltage, less amperage.
Most welders don't allow the change in voltage. Some old Lincoln engine welders do. For the rest of us a very tight arc gives less voltage, more amperage. Longer arc gives more voltage, less amperage.
Conversely, higher volts, lower amps will tend to snuff out the arc if held too close. the longer arc needed will tend to melt less deeply into the workpiece. Less contact with cooler steel means slower cooling of molten filler metal.
Other situations like thin metal laid flat work well with more voltage, less amperage.
Most welders don't allow the change in voltage. Some old Lincoln engine welders do. For the rest of us a very tight arc gives less voltage, more amperage. Longer arc gives more voltage, less amperage.
I have watched the video posted by fieldres and it is fine. He goes into great detail and it's all good information. I just really enjoy Jody's presentation style so I would like to see his take on the art and science of setting a SA200.
Steve
1966 Lincoln SA200 Redface
1990 Miller Dialarc 250
2003 Miller Maxstar STR
2015 Lincoln MP210
Victor & MECO torches
1966 Lincoln SA200 Redface
1990 Miller Dialarc 250
2003 Miller Maxstar STR
2015 Lincoln MP210
Victor & MECO torches
Bill Beauregard
- Bill Beauregard
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 9:32 pm
-
Location:Green Mountains of Vermont
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities