Search found 396 matches
- by sbaker56
- Wed Jul 13, 2022 8:40 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Tacking Stainless Nuts to Carbon Steel Plate?
- Replies: 5
- Views: 5889
Re: Tacking Stainless Nuts to Carbon Steel Plate?
In practical terms, no nothing terrible is going to happen, your nuts probably won't strictly be stainless anymore if they're allowed to overheat and if you use er70 series wire the weld is going to be prone to corrosion but there's absolutely nothing inherently wrong with welding carbon to stainles...
- by sbaker56
- Thu May 19, 2022 6:53 pm
- Forum: Product Reviews
- Topic: Stel P80 - 70A plasma cutter - 400V / 3-ph
- Replies: 1
- Views: 21972
Re: Stel P80 - 70A plasma cutter - 400V / 3-ph
Guessing the torch won't see much cutting anymore
- by sbaker56
- Thu May 19, 2022 6:42 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Mig welding with c10 gas
- Replies: 9
- Views: 9067
Re: Mig welding with c10 gas
You can short circuit just fine with 90/10. I LOVED the 93/7 mix I used one time when I was welding anything under 1/8". You'll lose a little bit of heat compared to 75/25 but it'll weld with a lot less spatter otherwise in my experience.
- by sbaker56
- Fri May 13, 2022 1:45 pm
- Forum: Welding Forum General Shop Talk
- Topic: auto darkening helmet
- Replies: 11
- Views: 7505
Re: auto darkening helmet
I'm a huge idiot that didn't even realize solar charging hoods were a thing, so I looked up my sentinel A50, and while a bunch of reviews said it had solar cells, I saw nothing about it on ESAB's website and to the best of my knowledge CR2450s aren't rechargeable so I'm guessing my hood doesn't cha...
- by sbaker56
- Thu May 12, 2022 8:51 pm
- Forum: Metal Cutting
- Topic: Are Cubitron 982C/987C still the best for rapid material removal?
- Replies: 2
- Views: 12416
Are Cubitron 982C/987C still the best for rapid material removal?
Not that Cubitron resin discs aren't already hard enough to get ahold of as is if you don't buy a whole case of 25. But the things are absolutely amazing. I am aware of their 982 CX pro version which susposedly cuts even faster but I've been entirely unsuccessful in finding out where to actually buy...
- by sbaker56
- Thu May 12, 2022 7:55 pm
- Forum: Metal Cutting
- Topic: Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
- Replies: 14
- Views: 16566
Re: Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
I went ahead and ordered the blade, and so far I've cut a couple pieces of 2" 3/16 flat bar like butter and also a 3" 3/8 coupon in half just as a test, it went right through that as well so it definitely cuts well.
We will see in the upcoming weeks how well it lasts.
We will see in the upcoming weeks how well it lasts.
- by sbaker56
- Thu May 12, 2022 7:44 pm
- Forum: Welding Forum General Shop Talk
- Topic: auto darkening helmet
- Replies: 11
- Views: 7505
Re: auto darkening helmet
I'm a huge idiot that didn't even realize solar charging hoods were a thing, so I looked up my sentinel A50, and while a bunch of reviews said it had solar cells, I saw nothing about it on ESAB's website and to the best of my knowledge CR2450s aren't rechargeable so I'm guessing my hood doesn't char...
- by sbaker56
- Tue May 03, 2022 11:49 pm
- Forum: Welding Projects - Welding project Ideas - Welding project plans
- Topic: Too many good looking projects here, figured I'd even things out a bit.
- Replies: 2
- Views: 14500
Re: Too many good looking projects here, figured I'd even things out a bit.
I had a bunch of little cut ends from building wood shed, I found if I split them into halves if I played with the blower just right I could get steel red hot with wood too, without the blower, it actually would probably make a pretty good grill
- by sbaker56
- Tue May 03, 2022 11:02 pm
- Forum: Welding Projects - Welding project Ideas - Welding project plans
- Topic: Too many good looking projects here, figured I'd even things out a bit.
- Replies: 2
- Views: 14500
Too many good looking projects here, figured I'd even things out a bit.
Here's what happens when you have a bucket full of scrap steel, a few too many beers and you regret selling your torch and being unable to heat things anymore, you make this thing. The main rule I had for this thing is that it had to be utterly free, I could not spend a single cent on it minus charc...
- by sbaker56
- Tue May 03, 2022 10:20 pm
- Forum: Stick Welding/Arc Welding - Shielded Metal Arc Welding
- Topic: Stel S300 on a 400V, 3-phase up-converting transformer
- Replies: 24
- Views: 20993
Re: Stel S300 on a 400V, 3-phase up-converting transformer
1200A?? I'm guessing a Subarc machine? I can't imagine anything else that could require that many amps, gouging probably, but on WHAT? No welding equipment, it's a machine. BIG machine. Has BIG motors on it. Just the main motor for it is 600HP. I'm told just that motor pulls around 750A continuous....
- by sbaker56
- Fri Apr 29, 2022 9:08 pm
- Forum: Stick Welding/Arc Welding - Shielded Metal Arc Welding
- Topic: Stel S300 on a 400V, 3-phase up-converting transformer
- Replies: 24
- Views: 20993
Re: Stel S300 on a 400V, 3-phase up-converting transformer
1200A?? I'm guessing a Subarc machine? I can't imagine anything else that could require that many amps, gouging probably, but on WHAT?
- by sbaker56
- Fri Apr 29, 2022 9:04 pm
- Forum: Metal Cutting
- Topic: Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
- Replies: 14
- Views: 16566
Re: Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
My saw is what appears to be an old discontinued northern tool equivalent to an evolution circular saw. It runs at 3500RPM rather than the more typical 5800 RPM of a standard circ saw. RPM does play a big role in tooth durability I believe, I've had occasions where my saw has been anything but smoot...
- by sbaker56
- Sun Apr 24, 2022 9:58 pm
- Forum: Metal Cutting
- Topic: Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
- Replies: 14
- Views: 16566
- by sbaker56
- Sun Apr 24, 2022 9:20 pm
- Forum: Metal Cutting
- Topic: Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
- Replies: 14
- Views: 16566
Would anyone actually be interested to see a Benchmark Abrasives TCT blade tested out?
Would anyone actually be interested to see a Benchmark Abrasives TCT metal cutting blade tested out? My saw has a 20mm arbor to begin with and I've just been getting by with surprisingly good luck using the diamond punch out with the 48 tooth diablo disks. As much crap as I put my saw through on top...
- by sbaker56
- Sun Apr 24, 2022 8:22 pm
- Forum: Welding Forum General Shop Talk
- Topic: best way to remove surface rust
- Replies: 3
- Views: 2858
Re: best way to remove surface rust
What Oscar said
- by sbaker56
- Sat Apr 23, 2022 4:33 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: How hot does your tig torch get?
- Replies: 22
- Views: 10539
Re: How hot does your tig torch get?
If I feel the heat through my glove enough for it to start to feel comfortable with a 17 torch I usually just take it as a sign that it's time to stop, let the machine cool, let the torch cool, and perhaps most importantly let the part cool while I hydrate for a few minutes, I know that's not always...
- by sbaker56
- Sun Apr 17, 2022 7:43 pm
- Forum: Welding Forum General Shop Talk
- Topic: Anyone tried these on mill scale?
- Replies: 8
- Views: 3834
Re: Anyone tried these on mill scale?
Yup, I've played with acid extensively on home projects in an attempt to both be lazy and to avoid leaving gouge marks in everything, vinegar will work in a pinch when let sit for a good while especially on reasonably light scale, and mixing up a batch of fresh citric acid works quite well too in my...
- by sbaker56
- Thu Jan 13, 2022 11:57 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: PLUG weld aluminum question
- Replies: 14
- Views: 2686
Re: PLUG weld aluminum question
Tig for sure, and it shouldn't show if properly welded with the right filler, depending on the aluminum alloy you happen to be welding, 5356 could be a better choice as it won't discolor/oxidize as weirdly as 4043 can but it depends on the alloy. If it'll be anodized or exposed to anything remotely ...
- by sbaker56
- Thu Jan 13, 2022 11:35 pm
- Forum: Member Introductions
- Topic: Hello
- Replies: 13
- Views: 3177
Re: Hello
I only ever weave in two situations with mig, when I'm running uphill, running downhill on thin material with a large gap or open root plate/pipe beveled to a knife edge. In any of those aforementioned situations you REALLY want to make sure you're in short circuit mode and not globular unless you h...
- by sbaker56
- Thu Jan 13, 2022 11:17 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: First Mistake - New to TIG
- Replies: 156
- Views: 83150
Re: First Mistake - New to TIG
Not becoming comfortable with the foot pedal will only steepen the learning curve in the long run. While not as entertaining, I'm a very big believer on running a bead pad on thicker material to become more proficient at anything you struggle with, practicing joints raises the difficulty and the cos...
- by sbaker56
- Thu Jan 13, 2022 10:26 pm
- Forum: Welding Forum General Shop Talk
- Topic: Setting up new shop- need ideas
- Replies: 10
- Views: 3398
Re: Setting up new shop- need ideas
Seems like if you have a plasma table EVERYONE is interested, at least that's been my perspective of seeing shops occasionally stop by the school hoping to make a deal to get parts cut out. If it's set right the cut quality is good enough no finishing is necessary for many things other than to prep ...
- by sbaker56
- Tue Jan 11, 2022 2:16 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: What is Best Practice to Bridge a Wide Gap
- Replies: 8
- Views: 2992
Re: What is Best Practice to Bridge a Wide Gap
I've ran a bead along one of the two edges before which helped bridge the gap, then ran a second pass to tie the now smaller gap together, and also used the whole lay a piece of 1/8" filler in the gap and blast it in before laying a bead over the top method before. I'd suggest the second one fo...
- by sbaker56
- Tue Jan 11, 2022 2:07 am
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Argon tank empty??
- Replies: 11
- Views: 9223
Re: Argon tank empty??
:x Wow over 30lbs difference huh? I plugged it into a gas volume to weight calculator and got the same result, I always just figured the things felt heavier on the trip back home than loading them into the truck because I was already dreading doing it a second time after having to do it once earlier...
- by sbaker56
- Fri Dec 24, 2021 7:32 pm
- Forum: Member Introductions
- Topic: Late to the game
- Replies: 8
- Views: 3065
Re: Late to the game
Agreed, nobody is just going to jump into stick and run it well, some people can get passably decent a whole lot faster with mig than you'd think, especially if the machine is set right. But stick, you've just got to burn about 20-30lbs of rods running bead pads and filling up T joints before it'll ...
- by sbaker56
- Thu Dec 23, 2021 7:49 pm
- Forum: Metal Cutting
- Topic: Metal cutting circular saw for beveling plate?
- Replies: 2
- Views: 10042
Metal cutting circular saw for beveling plate?
Believe I saw a thread about this a long time ago, unless you don't exactly need the practice, it's not much fun to do an open root weld with gouged up uneven poorly beveled plate that you tried to do with an angle grinder and a rather lacking amount of skill with it. I've gotten to where I can do a...
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities