This is the pic

I need the insulator for the back cap

The back cap insulator on my tig torch needs to be replaced. It is a 20 series torch wp280 miller anybody know where to buy one. All I see in my search is the front one that goes behind the cup need the one on the backside of the torch head
Thanks

I have good results with the diamond ground tri-mix cream color. Pricey but works well on Aluminum for me. I'm using a miller dynasty

great cup so far hope to get some more use this week with it.


Rob

Just got the furick 12 tried it out on some 1/8" stainless really good gas coverage Nice looking fillet there, is the Furick a 1" cup? I believe it is 3/4". Will measure tomorrow. First time giving it a shot had the stick out way out and seemed to still cover good was at about 25cfh

Just got the furick 12 tried it out on some 1/8" stainless really good gas coverage

jeff get some new 4043 maybe you have a bad batch. craig I believe I do. I have tried balancing it out, speeding up my travel, using less heat, you name it. From what I hear that 4943 is better but my LWS doesn't have it. Maybe time to roadtrip to HTP/USAweld What you have your balence at? I have a...

Practice practice and more practice, great video Jody has about just running beads. Get a piece of 1/8" aluminum and just run beads on it. Play around spacing when you add filler and just practice. Aluminum you can just run beads on beads. The pic is 1/8" thick using 3/32 filler

Thanks this is the one that I could bust apart split right down the middle of the weld

I will stop by the LWS for some 4943

yes 6061

The pieces were small. 5"X1" 1/4" thick. Took a few hits with the hamer I know the heat build up is a lot on the small pieces it was just some scrap I had laying around. If I put more heat into it would become a melted mess. Had the machine at 150 herz then tried it around 230. With 6...

anybody have some tips on 1/4" thick aluminum? Been messing around with some outside corners and butt joints. I can't get the weld to hold by what I mean I would but the piece in a vice and be able to break the joint the weld cracks right in the middle. running about 200-215 amps getting a good...

have a job coming up and all the welding is going to be done out of position on my back etc figure it is a good time to pick up a finger control unit. any suggestions? the machine is a dynasty 280 with the wp280 torch looking at the ck linear and rotary control and also miller NS and EW

[img][IMG]http://i685.photobucket.com/albums/vv211/75highboy/Mobile%20Uploads/image.jpg[/img][/img]

Trying to get the pic posted not the link

I plan on making a jig. Use some rectangular tubing and have some uprights with some clamps.

looking for some advise here have a job coming up for a friend he wants me to weld the center section of a axle to the tubes and then weld trusses to the axle it is a dana 44 He told me the center section is cast steel. has anybody done this? And how to tell for sure it is cast steel not cast iron?

thinking about doing the same thing if you can post up what you finally did it would be great.
would this kit help you?
https://www.arc-zone.com/flowmeters-reg ... -inlet-kit

I ended up buying the diamond ground piranha 2. I bought a refurbished machine which was a lot less then a new and still the 1 year warranty

Update got the new sharpener last week. Very nice machine can adjust the angle from 10-60 degrees. And puts a real nice point and finish on the tungsten. The only thing I would like it to be able to sharpen 1/8" tungsten. But I bought it knowing that.

i pulled a triger on the diamond ground piranha 11 refurbished machine was much cheaper then a new one I will post when I receive it

Thanks guys I do like the price of the HF blade sharpener but I think I am going to go with the tech south I like the hand held size and the consistent angle of the grind

all three seem to have all the same features. I like the adjustable grind angle feature what are the main differences between the three? is one better quality then the other? all seem kinda close in price with the sharpie first then the tech south then the htp