Hi frequency pulsing can stiffen the arc. They said that, but still have no chance to prove it since my welder only has low freq pulse (0,25-10Hz). Really wanna have a inverter machine that could pulsing hi frequency.

Thanks Steve, but I mean gas saver, not gas lens. Or they are the same?

Rgds,
Steph.

How a gas saver save the gas we used? By decreasing the flow rate? I mean, when we used Gas Saver we may decreased the flow rate to 40% compared to non gas saver? Or?..
Need info from you guys that used to use Gas Saver.
Thank you.
StephanusThie

Would anybody here explain please? What is it use for?? When we need to use this kind of collet??

Thank you in advance.
Steve.

Yes, I used 1,5% lanth.

Currently own a Sync250DX that cant adjust AC frequency and I always wondering "Does hi AC frequency make a big difference" in tig weld inside corner joint aluminum? Would you guys share your tipsandtricks to tig weld inside corner joint alum?? The problem I'm facing is arc wander/dancing ...

Hi guys, need you to share your experience in cutting 4mm thick alum or ssteel plate using plasma cutter. Is the cut clean enough to tig weld?
Please share. Thank you.

Steve.

Too hot maybe?? Turn down your amps a little bit lower.

Why do we need check valves? For security??

Guys would you tell me what is the most forgiving/easier process in welding aluminum, TIG or MIG? The answer should be based on your experience.
Thanks,
Steve.

Can pure Argon used to migging stainless steel?? This is because in my living place we cant find trimix. Or what gas is used to replace trimix??? They only have Argon, CO2 and He here. No mix gas.

Any suggestions?? Thank you.

Steph.

:oops: :oops: Hi Guys, I'm a nub, wanna learn to repair weld alum boat. Never do this before. Would you please share your experience in repair weld alum boat??? All I wanna know is what is your equipment, the settings, what's the commonly material the boat made of, what is the suitable wire/rod, how...

With single flowmeter wouldn't the flow be divided by 2?

Hi Jody, just wanna say Merry Christmas to you and all guys who supported www.weldingtipsandtricks.com.
Also Merry Christmas to all of you member of this forum..Wishing you all the best!!! May God Bless Us!!!

Me too.
I learn and practice tig and stick from this helpful site.
Thank you Jody.
May God bless you always.

How did you clean it? I always having problem cleaning cast alum, specially on repair work. Any help would be greatly appreciated. Thanks.

Guys, need your opinion based on your experience. Know that acetone is commonly used to clean alum, but here in town I live there's no chemical store. So Acetone we got here is from a supermarket, it's in form of 'nail polished remover'. While Alcohol and Thinner is easy to find in this town. The qu...

I made mine of mild steel plate and now am tired of cleaning it from red corrosion every 2 weeks.
I need suggestion please, on how to make a good and cheap welding table!!!
Thank you all in advance.

Thank you Kerm, I'll pay attention to what you suggested.

Hi guys, Back here again to get some help from you. Early in August I added a Pulse Module to my Miller Syncrowave 250DX. I then tried it. It works okey on DCEN. I can see the arc pulsing. Then I tried it on ACHF but can't see the arc pulsing. I'm a noobie in tig welding sooo please help me..Did I m...

As I remember, Viking is 588gr and Elite is 510gr.
Have you ever get flashed when wearing Elite??
Need more info about Viking. Just to make comparison. Thanks!!

I'm planing to buy a new auto darkening helmet, heard that Miller Elite Series is good(355$). Digital elite is better but more pricey(389$). Can't afford it. Do a little search on the internet, found Lincoln Viking Black 2450 is almost the same specs with Elite Series, but a little more weight, the ...

Hi,
i'm a beginer in tig welding at "trial n error" level.
In your case, maybe the amp you set was too high.
i usually use 3/32 at only 175/180 amps. Wanna higer
Amps than that you should use 1/8 Tungs.
Hope this usefull..